Bedside power for your dorm.

Satin black

Railnest hangs your power strip beside your mattress, so you can charge your phone and keep your desk clear. The hooks fit exposed, flat-sided ¾-inch and 1-inch dorm bed rails.

$19.00
Fits two common dorm rail sizes
1 inch 25.4 mm
Use both hooks directly on the rail.
¾ inch 19.05 mm
Fit one included liner inside each hook.
How to measure your rail Installation guide

In the set  One carrier, two keyed hooks, two rail liners and two thin hook-and-loop straps. Power strip sold separately.

A spot for your charger.

When your phone is at 3%, you shouldn’t have to reach under the bed for the plug. With the outlets facing you, you can plug in from your mattress. On a lofted bed or top bunk, that also saves a trip down the ladder.

See how it mounts
A white power strip held by two black straps on a maple dorm bed rail, with the cord exiting on the left

How the mount works

Twin rail hooks

The hooks sit near opposite ends of the carrier. Fit the supplied liners inside them for a ¾-inch rail.

Two retention straps

The thin hook-and-loop straps pass through the carrier and around each end of your strip. Position them between outlets.

Open cord exit

The cord exits through the gap between the end prongs, giving it a clear path toward the wall outlet.

Find the fit for your dorm bed.

Measure across the top of the rail, between its two flat faces. Check at both hook locations, about 6 inches apart. The hooks need an exposed top edge and room behind the rail.

1 in 25.4 mm
Use the bare hooks. Hang both hooks directly over the rail.
¾ in 19.05 mm
Use the included liners. Slip one liner inside each hook before hanging the mount.

What changes when you mount your strip?

FeaturePower strip on its ownPower strip with Railnest
Outlet locationWherever the strip restsAt the height of your bed rail
Floor or desk spaceThe strip takes up surface spaceThe carrier hangs from the side of the bed
Cord positionThe strip can shift as cords moveTwo straps hold the strip, and its cord exits between the end prongs

Dimensions & fit

Measure the thickness of your rail across its top edge. Both hooks need an exposed, flat-sided section with room behind it.

Rail thickness
1 in (25.4 mm) with bare hooks, or ¾ in (19.05 mm) with one liner per hook
Hook opening
1.022 in (25.95 mm) bare, 0.764 in (19.40 mm) lined
Hook dimensions
1.02 in along the rail × 1.99 in across × 2.26 in tall
26.0 × 50.45 × 57.4 mm
Hook spacing
5.98 in (152 mm) center to center
Carrier length
8.36 in (212.4 mm)
Assembled Railnest carrier, two black straps, and two removable rail liners

What’s in the box?

  • One satin-black power strip carrier
  • Two keyed bed rail hooks
  • Two removable ¾-inch rail liners
  • Two thin hook-and-loop straps

Power strip sold separately.

Install your Railnest

  1. Choose your rail fit

    Use the hooks directly on a 1-inch rail. For a ¾-inch rail, fit one liner inside each hook.

  2. Hang the carrier

    Lower both hooks over the rail together. Seat them fully with the carrier facing the side where you want the outlets.

  3. Position the power strip

    Rest the strip horizontally on the two lower supports with its outlets facing you. Run the supply cord between the two prongs at the end.

  4. Fasten both straps

    Wrap one strap around each end of the strip and fasten it against the carrier. Keep the outlets, switch and cord exit clear.

Before you order

Will Railnest fit my dorm bed?

Look for an exposed, flat-sided rectangular rail that’s 1 inch thick, or ¾ inch with the included liners. Leave enough room behind the rail for both hooks to sit fully over it. Round tubes and padded rails need a different mount. See the hook dimensions.

How do I check my power strip?

Compare your strip with the 8.36-inch carrier. Check that both straps can wrap around the strip between outlets and that the supply cord can exit between the end prongs.

Can I move it to another spot?

Disconnect the strip, release both straps and lift out the strip. Lift the hooks clear of the rail and check the rail width at the new spot before reinstalling.

Ask a question